U600-Flashing [Upute,Programi]

[aco_kuna]

Hteo sam da Flesujem U600 da bi promenio Jazike ali posle Flesa telefon samo Pise Samsung U600 i nista vise ,,jel zna neko ikakvu pomoc za ovu stvar

Flesao sam sa USB Kablom i sad PC ne Prepoznaje Telefon

[aco_kuna]

Moze li neko prevesti na Hrvacki ova teks koi sluzi za Flash


1. Make sure you have U600 Optiflash, a Samsung SGH-U600 flash file and the original samsung USB cable that came with the phone.

2. Install the USB driver for the cable.

3. Launch Optiflash and click on "Options > Settings > Generic"
- Select "Customer T: D830/D840/D910/X840/ECLAIR TFS16(USB)"
- Set "Flash Erase Passes" to "1"
- Set "Operation Passes" to "Default"
- If the phone has an asian or european firmware and the new firmware is also asian or european respectively, then uncheck all checkboxes except "Differences Only". If the region of the new firmware is different than the old one then uncheck all checkboxes except "Differences Only", "Erase All Unused Regions" and "Extended Protection".

4. Select the tab "Read" and make sure that under the "Read Ranges" there is "0x20000000 - 0x21ffffff" because if it isn't, it may wipe your imei. You can check your imei by typing *#06#.

5. Select the tab "Flash and Verify"
- Browse to and select your *.s3 firmware file

6. Select the tab "Default Contents"
If you have a file *.cts with the firmware *.s3:
- Select radio button "S-Record with Contents"
- Browse to and select your *.cts file

If you do not have the file *.cts:
- Click on "S-Record only"

- Click "OK"

7. Connect the phone to the computer via the USB cable. In the phone click "connect to pc studio".

8. Remove your SIM, your microSD card and the battery from the phone which will turn the phone off. Leave the USB cable in. You will see leds on.

9. Whilst holding down the * key on the phone, briefly press the ON button. Your computer will recognise the device as Samsung USB Mobile.

10. Return to Optiflash, click on "Options > Settings > COM Port"
- Select the COM port your phone uses. If you are not sure, you can find out by: Control Panel > System > Hardware > Device Manager > Ports (COM and LTP).
- Select "921600".
- In Second COM Port select "none"

- Click "OK"

Lastly, click "Flash"

The flash procedure takes approximately 15 minutes and will be finished when the message "All is Well" appears above the green progression bar.

A full reset should not be necessary once the firmware is upgraded, however, if you want to do it type *2767*3855# then wait one full minute before you restart your phone.

To check your existing firmware type *#1234# into your handset.

If your phone restarts in a different language follow the language selection process:

MENU (left touch button) > SETTINGS (bottom right icon) > PHONE SETTINGS (2nd option) > LANGUAGE (1st option)


If the phone freezes after flashing you may need to wipe your regions. Go to "Options > Settings > Generic" and uncheck all checkboxes except "Differences Only", "Erase All Unused Regions" and "Extended Protection".

[HSV]

@aco_kuna

1. Budite sigurni da imate U600 Optiflash,Samsung SGH-u600 flash fileove i orginalni samsung USB kabel koji je došao s mobitelom.
2. Instalirajte USB driver za kabel.
3. Pokrenite Optiflash i izaberite"Options > Settings > Generic"
-izaberite "Customer T: D830/D840/D910/X840/ECLAIR TFS16(USB)"
- postavite "Flash Erase Passes" to "1"
- postavite "Operation Passes" to "Default"
- ako mobitel ima Azijski ili Europski firmware i novi firmware je Azijski ili Europski odnosno,odznačite sve kvadratiće osim "Differences Only"
-Ako je regija novog firmwarea nije ista kao stara onda odznačite sve kvadratiće osim "Differences Only","Erase All Unused Regions" and "Extended Protection".

4 Izabretie oznaku "Read" i provjerite da je pod "Read Ranges" vrijednost "0x20000000 - 0x21ffffff",ako nije izbrisat će imei
Možete provjeriti imei *#06#

5 Izaberite oznaku "Flash and Verify"
- Potražite i izabreite svoj *.s3 firmware file

6 Izaberite oznaku "Default Contents"
Ako imate file *.cts sa firmware *.s3:
-izaberite radio button "S-Record with Contents"
-pretražite i izaberite svoje *.cts file

Ako nemate file *.cts
-Kliknite na "S-Record only"
-Kliknite na "OK"

7 Povežite mobitel putem USB-a,u mobitelu izaberite "connect to pc studio"

8 Izvadite Sim,micro SD karticu i bateriju iz mobitela što će isključiti mobitel
-ostavite usb kabel u mobitelu

Dok držite tipku * na mobitelu kratko pritisnite ON tipku,PC će prepozanti uređaj kao Samsung USB Mobile.

10 Vratite se na Optiflash idite na "Options > Settings > COM Port"
-izaberite COM port što ga mobitel koristi,ako niste sigurni koji je port idite na Control Panel > System > Hardware > Device Manager > Ports (COM and LTP).

- izaberite "921600".
- U drugom COM Port izaberite "none"

Pritisnite Ok

-Procedura flashiranja traje 15 minuta i nakon što je završeno piše "All is Well"

-Reset nije potreban nakon što je firmware nadograđen, a ako to želite učiniti upišite *2767*3855# i mob će se resetirat

-Za provjeru firmware-a upišite *#1234#

-ako se mobitel resetira na drugom jeziku idite na Izbornik-postavke-postavke mobitela-jezik

-Ako se mobitle zamrzne nakon flashiranja morate izbrisati regije idite na "Options > Settings > Generic"odznačite sve kvadratiće osim "Differences Only","Erase All Unused Regions" and "Extended Protection".

i

[aco_kuna]

HSV Veliko Hvala za ovo sto si se potrudio za prevodu ,Trebace ovo za druge Clanove ja sam resio moj slucaj i Uspeo sam da ga Razbudim Telefon i da uspesno Flesujem nakon 4 Obida ,,Jos jednom Hvala i svaka Cast za Trudu