Printable View
Ako kako kome treba može skinuti na sljedećoj stranici:
http://homepages.pathfinder.gr/xux99/samsung/
Na jednom forumu sam pročitao da u600 ne zahtjeva poseban kabel za flash, nego se koristi onaj usb koji dobiješ uz njega, mislim super ak je tak pošto vidim da je za d900 dosta teško nać flash kabel.
nije potreban flash kabel, sve se radi s USB-om.
Treba ti samo firmware i U600 Optiflash.
kak da vidim koji softver imam ?
i koij je najnoviji ?
Utipkaj *#1234# onda ce ti pokazat koji FW imas!= Citat =:
Izvorno postao Fran Mirtl
imam xfgd2.
jel ima koji noviji / bolji ?
= Citat =:
Izvorno postao Fran Mirtl
Pa pogledaj prvi post!
stavio ovaj najnoviji , i nema nikakve razlike
osim kaj nemam vise hr :D
hehe :) ja imam ovoga kojeg tu niti nema :))
U600XFGD5
xf ne xe= Citat =:
Izvorno postao exotica
hrvatski meni u sebi ima
XFGD2 ti ima HR !
to mi je jasno, no ja velim da imam U600XFGD5 i da imam hrvatski meni na njemu= Citat =:
Izvorno postao exotica
jel more neko uploadat negdje ovaj u600xfgd5 jel ga nema nigdje za skinut ?
nasao dva sajta al nedaju skinut s njih.....
Narode jel ima kakvih naznaka za u600 mod, tj jel netko uspio dekompresirati firmware?
ej a sta je sa ovim firmvareom koji je kod mene U600DXGG2
Mobitel sam tokom flashiranja isključio iz pc-a misleći da je gotovo i sad više ne radi.Kad ga idem upalit, boot slika se pokaže i ugasi se.
Što mi je raditi s obzirom da ga driveri više ne prepoznaju?
Molim pomoć!
U600XFGD2 kod mene nema hrvatski a kod vas neznam
ne znam jos dok ne stavim normala softwer...vec je 10tak dana po servisima
evo ondej ima
http://rapidshare.com/users/WICSIK
flesh putem boxa.
Ma moze i preko USB-a, samo treba pravodobno postavit postavke flashiranja i stime da baterija mora biti puno.
Ako se mob ne pali moguce je sve, 1. Sprzen Flash Chip, 2. Flash nije sjeo kako treba jer je baterija bila slaba, 3. Postavke nisu podesene kako treba!
Ja se slažem sa exoticom ili si je jednostavno "umro"
Najprije probaj još od d900,d900i ili još nekog samsunga pa onda probaj ručno.= Citat =:
Izvorno postao markof72
Hteo sam da Flesujem U600 da bi promenio Jazike ali posle Flesa telefon samo Pise Samsung U600 i nista vise ,,jel zna neko ikakvu pomoc za ovu stvar
Flesao sam sa USB Kablom i sad PC ne Prepoznaje Telefon :cry: :cry:
Moze li neko prevesti na Hrvacki ova teks koi sluzi za Flash
1. Make sure you have U600 Optiflash, a Samsung SGH-U600 flash file and the original samsung USB cable that came with the phone.
2. Install the USB driver for the cable.
3. Launch Optiflash and click on "Options > Settings > Generic"
- Select "Customer T: D830/D840/D910/X840/ECLAIR TFS16(USB)"
- Set "Flash Erase Passes" to "1"
- Set "Operation Passes" to "Default"
- If the phone has an asian or european firmware and the new firmware is also asian or european respectively, then uncheck all checkboxes except "Differences Only". If the region of the new firmware is different than the old one then uncheck all checkboxes except "Differences Only", "Erase All Unused Regions" and "Extended Protection".
4. Select the tab "Read" and make sure that under the "Read Ranges" there is "0x20000000 - 0x21ffffff" because if it isn't, it may wipe your imei. You can check your imei by typing *#06#.
5. Select the tab "Flash and Verify"
- Browse to and select your *.s3 firmware file
6. Select the tab "Default Contents"
If you have a file *.cts with the firmware *.s3:
- Select radio button "S-Record with Contents"
- Browse to and select your *.cts file
If you do not have the file *.cts:
- Click on "S-Record only"
- Click "OK"
7. Connect the phone to the computer via the USB cable. In the phone click "connect to pc studio".
8. Remove your SIM, your microSD card and the battery from the phone which will turn the phone off. Leave the USB cable in. You will see leds on.
9. Whilst holding down the * key on the phone, briefly press the ON button. Your computer will recognise the device as Samsung USB Mobile.
10. Return to Optiflash, click on "Options > Settings > COM Port"
- Select the COM port your phone uses. If you are not sure, you can find out by: Control Panel > System > Hardware > Device Manager > Ports (COM and LTP).
- Select "921600".
- In Second COM Port select "none"
- Click "OK"
Lastly, click "Flash"
The flash procedure takes approximately 15 minutes and will be finished when the message "All is Well" appears above the green progression bar.
A full reset should not be necessary once the firmware is upgraded, however, if you want to do it type *2767*3855# then wait one full minute before you restart your phone.
To check your existing firmware type *#1234# into your handset.
If your phone restarts in a different language follow the language selection process:
MENU (left touch button) > SETTINGS (bottom right icon) > PHONE SETTINGS (2nd option) > LANGUAGE (1st option)
If the phone freezes after flashing you may need to wipe your regions. Go to "Options > Settings > Generic" and uncheck all checkboxes except "Differences Only", "Erase All Unused Regions" and "Extended Protection".